PANASONIC CM/TF800



NOTES:  This is a dual NAM unit.

        The ESN prefix is 136 decimal & 88 hex.

        Panasonic: 201-392-6053





NAM PROGRAMING:



1.  Turn power on.



2.  Within 20 seconds enter * 0 # 0 * 0 # 0 * 1 for NAM 1

    or * 0 # 0 * 0 # 0 * 2 for NAM 2.



3.  Each data entry can be looked at by pressing RCL followed by the

    location (step) number below.



4.  To store new data enter the value, press STO followed by the location

    (step) number below.  For example to enter a system ID of 00031 enter

    00031 STO 01.  Data can be entered or reviewed in any order.



5.  At any time press STO * * to complete programing.



6.  Press END to exit.







PROGRAMING DATA:



STEP#    #OF DIGITS/RANGE    DISPLAY        DESCRIPTION



01       00000 - 32767       SIDH           SYSTEM ID

02       10 DIGITS           OWNDL          MIN (AREA CODE & TEL NUMBER)

03       0 OR 1              PRESYS         PREFERRED SYSTEM

04       333 OR 334          IPCH           INITIAL PAGING CHANNEL

05       2 DIGITS            ACCOLC         ACCESS OVERLOAD CLASS

06       2 DIGITS            GIM            GROUP ID (10 IN USA)

07       2 DIGITS            DLMT           DIALED DIGIT LIMIT (00= NO LIMIT)

08       08 ONLY             SCM            STATION CLASS MARK

09       UP TO 12 DIGITS     SPDL           SPEED DIAL NUMBER (PERMANENT

                                            NUMBER STORED IN LOCATION 00)

10       2 TO 4 DIGITS       LOCK           LOCK CODE

11       8 DIGIT, 0 OR 1     FCN 1          SEE NOTE 1 BELOW.

12       8 DIGIT, 0 OR 1     FCN 2          SEE NOTE 2 BELOW

13       8 DIGIT, 0 OR 1     FCN 3          SEE NOTE 3 BELOW





NOTES:



1.  Suggested entry is: 11000000.



Bit 7/Digit 1 = Local use Mark

Bit 6/Digit 2 = MIN Mark

Bit 5/Digit 3 = Not Used

Bit 4/Digit 4 = Not Used

Bit 3/Digit 5 = Not Used

Bit 2/Digit 6 = Horn Alert

Bit 1/Digit 7 = Radio Mute

Bit 0/Digit 8 = Not Used



2.  Suggested entry is: 00010100.



Bit 7/Digit 1 = Not Used

Bit 6/Digit 2 = Built in Monitor

Bit 5/Digit 3 = Auto Lock

(if set to 1 and unlock code is unknown phone will NOT enter program mode.)

Bit 4/Digit 4 = Full Lock

Bit 3/Digit 5 = Not Used

(Enable only one of the following)

Bit 2/Digit 6 = Allow user A/B select

Bit 1/Digit 7 = Preferred system only

Bit 0/Digit 8 = Home system only (no Roam)



3.  Suggested entry is: 11000111.



Digit 1 = Received call indicator

Digit 2 = Continuous DTMF

Digit 3 = Not Used

Digit 4 = Dial Lock

Digit 5 = Not Used

Digit 6 = Enable permanent timer (FCN 1)

Digit 7 = Enable resetable timer (FCN 2)

Digit 8 = Enable individual call timer





READING ESN FROM HANDSET:



1.  Power up phone as above.



2.  Enter * 0 0 0 0 #.



3.  Press * 3 SND.



4.  Press 1 1 SND, phone will display decimal ESN, note that the leading

    "1" of the 136 ESN prefix will be omitted as the phone only has a ten

    digit display capacity.



LOCK: F 3 2 = Dial Lock, F 3 1 = Send lock, F 3 0 = Full lock



UNLOCK: Enter two to four digit code.





A/B SYSTEM SELECT:



1.  Phone will default to preferred/non-preferred on every power up.



2.  A only: F 7 2



3.  B only: F 7 3



4.  Home only: F 7 4