PANASONIC EB 2500/2501/2502, TP 500/800 SERIES.



NOTES:  This is a dual NAM mobile or transportable unit.

        The ESN prefix is 136 decimal & 88 hex.

        Panasonic: 201-392-6053





NAM PROGRAMING:



1.  This unit requires a programing adaptor, part number EB-W0134, if you

    do not have one try one of the following:



If the phone has a transportable pack with a charged battery you can jump

pins 2 and 3 of the power connector with a paper clip or tweezers.  With

the transceiver right side up (rubber feet on the bottom) look at the power

connector, pin 2 is bottom right, and pin 3 is top center.  In the

following diagram the X marks the top of the connector where the plastic

clip on the power cord is:



                                 X

                               5 3 1

                               6 4 2



Ignore any numbers stamped on the connector and remember this shows the

power connector looking at the transceiver, or wire side of the power cord.



If the phone does not have a transportable pack you can remove the plastic

cap from the power cord and jump pins 2 and 3 as above.



2.  Turn power on with pins 2 and 3 jumpered.



3.  Enter * 0 0 0 0 #, phone will display "0", you are now in maintenance

    mode.



4.  Enter * 1 SND for NAM 1, or * 2 SND for NAM 2.  Phone will display "1"

    or "2".  Note that NAM 2 has entries 01 through 06 only.



5.  Each data entry can be looked at by pressing RCL followed by the

    location (step) number below.



6.  To store new data enter the value, press STO followed by the location

    (step) number below.  For example to enter a system ID of 00031 enter

    00031 STO 01.  Data can be entered or reviewed in any order.



7.  At any time press STO * * to complete programing and return to

    maintenance mode.



8.  At any time press STO # # to ABORT programing and return to maintenance

    mode.



9.  Press * 4 SND to exit maintenance mode.





PROGRAMING DATA:



STEP#    #OF DIGITS/RANGE    DESCRIPTION



01       00000 - 32767       SYSTEM ID

02       10 DIGITS           MIN (AREA CODE & TEL NUMBER)

03       0 OR 1              PREFERRED SYSTEM

04       333 OR 334          INITIAL PAGING CHANNEL

05       2 DIGITS            ACCESS OVERLOAD CLASS

06       2 DIGITS            GROUP ID (10 IN USA)

07       2 DIGITS            DIALED DIGIT LIMIT (00= NO LIMIT)

08       08 ONLY             STATION CLASS MARK

09       UP TO 12 DIGITS     SPEED DIAL NUMBER (PERMANENT NUMBER STORED IN

                             LOCATION 00)

10       2 TO 4 DIGITS       LOCK CODE

11       8 DIGIT, 0 OR 1     SEE NOTE 1 BELOW.

12       8 DIGIT, 0 OR 1     SEE NOTE 2 BELOW

13       8 DIGIT, 0 OR 1     SEE NOTE 3 BELOW





NOTES:



1.  Suggested entry is: 11000100.



Digit 1 = Local use Mark

Digit 2 = MIN Mark

Digit 3 = Not Used

Digit 4 = Not Used

Digit 5 = Not Used

Digit 6 = Horn Alert  (Select only if radio mute is "0")

Digit 7 = Radio Mute  (Select only if horn alert is "0")

Digit 8 = Not Used



2.  Suggested entry is: 00010100.



Digit 1 = Not Used

Digit 2 = Built in Monitor

Digit 3 = Auto Lock (if set to 1 and unlock code is unknown phone will NOT

                    enter program mode.)

Digit 4 = Full Lock

Digit 5 = Not Used

(Enable only one of the following)

Digit 6 = Allow user A/B select

Digit 7 = Preferred system only

Digit 8 = Home system only (no Roam)



3.  Suggested entry is: 11000111.



Digit 1 = Received call indicator

Digit 2 = Continuous DTMF

Digit 3 = Not Used

Digit 4 = Dial Lock

Digit 5 = Not Used

Digit 6 = Enable permanent timer (FCN 1)

Digit 7 = Enable resetable timer (FCN 2)

Digit 8 = Enable individual call timer





READING ESN FROM HANDSET:



1.  Power up phone with pins 2 and 3 jumpered as above.



2.  Enter * 0 0 0 0 #.



3.  Press * 3 SND.



4.  Press 1 1 SND, phone will display decimal ESN, note that the leading

    "1" of the 136 ESN prefix will be omitted as the phone only has a ten

    digit display capacity.



LOCK: F 3 2 = Dial Lock, F 3 1 = Send lock, F 3 0 = Full lock



UNLOCK: Enter two to four digit code.





A/B SYSTEM SELECT:



1.  Phone will default to preferred/non-preferred on every power up.



2.  A only: F 7 2



3.  B only: F 7 3



4.  Home only: F 7 4









 